镀铝板用耐高温型无铬钝化结合机理及性能

传统的有机类无铬钝化产品在400 ℃的高温条件下黄变较重,在保持优异的耐高温前提下,同时具有优异的耐蚀性和加工性能,设计了镀铝板使用的无机类加少量有机类的无铬钝化产品。利用电化学工作站、X射线光电子能谱、X射线荧光谱、红外光谱等方法,对该无铬钝化药剂在热镀铝板表面的成膜机理进行了研究,并结合成膜动力学分析,完成了皮膜与铝硅镀层的界面结合机理分析。对膜重、固化温度对镀铝板工艺性能影响进行研究,得出综合性能优异的膜重控制范围为0.8～1.2 g/m2,对应的PMT温度大于80 ℃。所生产的无铬钝化热镀铝板产品耐高温、耐腐蚀和冲压性能优异,400 ℃烘烤2 h后表面色差ΔE＜3,72 h中性盐雾试验未出现锈蚀。     

基于飞秒激光制备的光子晶体光纤Fabry-Perot温度传感器

提出并设计了一种基于飞秒激光在光子晶体光纤(photonic crystal fiber,PCF)中制备光纤法布里-珀罗(Fabry-Perot,F-P)传感器的方法。采用飞秒脉冲激光作为加工光源,结合放大倍率100×的物镜以及三维加工平台在PCF侧面采用逐线刻写方式进行加工。通过对飞秒激光光斑在光纤上的聚焦位置以及刻写功率进行优化,在PCF上刻写了深度均为80 μm、间隔为800 μm的两条划线,实现了周期为0.98 nm的全光纤F-P结构制备；实验中,对传感器在40~120 ℃温度范围内的光谱特性进行了测试与分析,每隔10 ℃进行一次数据采集,随着温度逐渐增加波长向长波方向漂移,通过对该采样点数据进行线性拟合,得到该测试点的波长温度灵敏度为9.73 pm/℃,拟合线性度为0.997。     

载气热提取法测定熔敷金属中扩散氢收集条件的探究

探究了GB/T 3965—2012《熔敷金属中扩散氢测定方法》中载气热提取法收集条件对测定扩散氢含量的影响,并与水银法进行了对比。研究结果表明,样本炉温设定为400℃,A型试块的内部温度大约在51 min时稳定在358℃左右,B型试块内部温度大约在27 min时稳定在391℃左右;载气热提取法电信号曲线收集结束点的电信号及斜率均接近0时获得的结果与水银法具有较好的一致性。     

Oxidation‐led decomposition of hexagonal boron nitride coatings on alloy substrates at 900 °C: Ti‐6Al‐4V

Hexagonal boron nitride (h‐BN) coatings on Ti‐6Al‐4V substrates undergo complete decomposition in air at 900 °C. This fate is similar to that of this ceramic material on chromia‐former alloys, and unlike that of a mass of powder treated in isolation. As the ceramic and alloy oxidize concurrently, outwardly diffusing aluminum (III) ions but not the predominant titanium (IV) ions react with the boron trioxide that forms around the h‐BN basal plane peripheries. Resultant aluminum borate is incorporated into the growing scale and the boron trioxide diffusion barrier is depleted. By this mechanism, the oxidation of h‐BN is maintained at an enhanced rate, until both this material and its oxide completely decompose. Liberated nitrogen from the oxidation of h‐BN can enter the underlying scale as a randomly distributed solute in rutile solid solution. The post‐coating oxide‐atmosphere interface comprises elongated aluminum borate crystallites protruding through at the boundaries between 3–5 at% nitrogen‐doped rutile grains. It differs significantly from that of oxidized, uncoated Ti‐6Al‐4V, which is occupied by a thin α‐alumina layer atop rutile. This interface does not change with an additional 72 h of heat‐treatment.     

罩式退火温度对高强IF钢组织及性能的影响

为研究不同退火温度下高强IF钢的组织性能及织构的变化规律,采用温箱式电阻炉加热模拟罩式退火工艺,研究了不同退火温度下高强IF钢210P1冷轧板力学性能;对不同退火温度钢板的r90进行了统计并对其进行显微组织观察;采用X射线衍射仪及热场发射扫描电镜对不同退火温度的罩式退火成品板进行了织构分析。结果表明,在高强IF钢210P1冷轧板的罩式退火过程中,提高退火温度将使晶粒明显长大。随着退火温度的升高,屈服强度及抗拉强度下降,伸长率升高,n值略有上升,板材横向r值增加较明显,有利织构{111}取向密度增加,不利织构{100}取向密度降低。     

迁钢210 t钢包全程加盖工艺及实践

迁钢二炼钢厂自投入使用210 t钢包全程加盖技术及工艺后，取得了显著效果，平均出钢温度降低10 ℃，钢包热周转使用率长期保持在85%以上，取消了钢包在线烘烤，降低了煤气消耗，有效地保证了钢包洁净度，提高了钢包包衬寿命。实践生产运行表明，炼钢生产中钢包全程加盖工艺是一项节能、环保、降耗的先进技术，为迁钢二炼钢厂取得了显著的经济效益。但在一段时间内，该工艺运行稳定性较差，通过现场生产数据归纳分析，从中找出了影响钢包加、揭盖的因素，并制定了控制措施；同时，岗位要掌握其操作要点及主要设备，才能提高运行稳定性。     

Microstructure and flexural strength of the Y:TZP/BG composite

The addition of bioactive glasses to a Y:TZP matrix represents a feasible alternative to provide bioactivity to this material and optimize osseointegration. This work evaluated the effect of the BG concentration (0 and 10 wt%) and the sintering temperature (1200°C and 1300°C) on the microstructure, relative density, and flexural strength of the composite Y:TZP/BG. The Y:TZP and Y:TZP/BG powders were uniaxially pressed and sintered at 1200°C or 1300°C for 1 h. The microstructure was characterized by X-ray diffraction analysis, scanning electron microscopy, and energy-dispersive X-ray Spectroscopy. Relative density was calculated from density values obtained using the Archimedes’ principle. For the flexural strength, specimens (n = 6) were fractured in a biaxial flexural setup using a piston-on-three-balls fixture in a universal testing machine. Bioactivity test was performed in simulated body fluid solution. The results suggested that BG addition decreased the grain size of the composite, increased porosity and caused a significant decrease in the relative density and flexural strength. Crystalline phases of calcium stabilized cubic zirconia and sodium zirconium silicate were formed after the addition of BG. Finally, it was concluded that composite specimens sintered at 1300°C showed the highest density values and larger grains compared to those sintered at 1200°C.     

钢包包衬侵蚀对内衬温度和钢水温降的影响

为了研究包衬侵蚀对钢水温降的影响规律,通过ANSYS有限元软件以及ParaMesh网格随移技术建立了考虑包衬侵蚀的钢包传热计算模型,研究并分析了包衬侵蚀对包衬及钢水温度的影响规律。结果表明,包衬侵蚀对包衬温度影响较大,在相邻两个修包周期内,包衬侵蚀造成渣线和包壁的包衬内部(工作层与永久层交界处)温差为14～114 K;包衬侵蚀导致包壳外表面温度升高,包壳向外散热增加,与此同时,包衬受侵蚀变薄,蓄热减少,两者同时作用导致包衬侵蚀对钢水温降影响不大,最高不超过1 K,在实际生产中可以适当地忽略钢包侵蚀对钢水温降的影响。     

等离子弧异质异构增材制造构件的组织与力学性能分析

采用等离子弧增材系统实现了不锈钢/高强钢异质异构增材构件制备，等离子弧增材构件具有良好的沉积形貌及优异的力学性能.为揭示叠合方式对等离子弧异质增材构件的宏微观组织和力学性能特征影响，研究采用了体视显微镜、金相显微镜、拉伸及硬度等测试方法.结果表明，不锈钢/高强钢异质异构增材构件中存在两种过渡形式，即以奥氏体枝晶过渡和马氏体组织过渡.增材构件横截面硬度波动较大，主要是混合过渡区域的高合金元素导致的组织变化引起的.叠合方式的改变能够显著影响材料性能，在强度下降不多的情况下，提高材料的冲击韧性.